收藏本站
25AA040/25LC040/25C040
3.0
FUNCTIONAL DESCRIPTION
3.3
Write Sequence
3.1
Principles of Operation
Prior to any attempt to write data to the 25XX040, the
write enable latch must be set by issuing the WREN
The 25XX040 is a 512 byte Serial EEPROM designed
to interface directly with the Serial Peripheral Interface
(SPI) port of many of today’s popular microcontroller
families, including Microchip’s PIC16C6X/7X micro-
controllers. It may also interface with microcontrollers
that do not have a built-in SPI port by using discrete
I/O lines programmed properly with the software.
The 25XX040 contains an 8-bit instruction register. The
part is accessed via the SI pin, with data being clocked
in on the rising edge of SCK. The CS pin must be low
and the HOLD pin must be high for the entire operation.
The WP pin must be held high to allow writing to the
memory array.
Table 3-1 contains a list of the possible instruction
bytes and format for device operation. The Most
Significant address bit (A8) is located in the instruction
byte. All instructions, addresses, and data are
transferred MSB first, LSB last.
Data is sampled on the first rising edge of SCK after CS
goes low. If the clock line is shared with other periph-
eral devices on the SPI bus, the user can assert the
HOLD input and place the 25XX040 in ‘HOLD’ mode.
After releasing the HOLD pin, operation will resume
from the point when the HOLD was asserted.
instruction (Figure 3-4). This is done by setting CS low
and then clocking out the proper instruction into the
25XX040. After all eight bits of the instruction are
transmitted, the CS must be brought high to set the
write enable latch. If the write operation is initiated
immediately after the WREN instruction without CS
being brought high, the data will not be written to the
array because the write enable latch will not have been
properly set.
Once the write enable latch is set, the user may
proceed by setting the CS low, issuing a WRITE
instruction, followed by the address, and then the data
to be written. Keep in mind that the Most Significant
address bit (A8) is included in the instruction byte. Up
to 16 bytes of data can be sent to the 25XX040 before
a write cycle is necessary. The only restriction is that all
of the bytes must reside in the same page. A page
address begins with XXXX 0000 and ends with XXXX
1111 . If the internal address counter reaches XXXX
1111 and the clock continues, the counter will roll back
to the first address of the page and overwrite any data
in the page that may have been written.
For the data to be actually written to the array, the CS
must be brought high after the least significant bit (D0)
of the n th data byte has been clocked in. If CS is
brought high at any other time, the write operation will
3.2
Read Sequence
not be completed. Refer to Figure 3-2 and Figure 3-3
The part is selected by pulling CS low. The 8-bit READ
instruction with the A8 address bit is transmitted to the
25XX040 followed by the lower 8-bit address (A7
through A0). After the correct READ instruction and
address are sent, the data stored in the memory at the
selected address is shifted out on the SO pin. The data
stored in the memory at the next address can be read
sequentially by continuing to provide clock pulses. The
internal Address Pointer is automatically incremented
to the next higher address after each byte of data is
shifted out. When the highest address is reached
(01FFh), the address counter rolls over to address
0000h allowing the read cycle to be continued
indefinitely. The read operation is terminated by raising
the CS pin (Figure 3-1).
for more detailed illustrations on the byte write
sequence and the page write sequence respectively.
While the write is in progress, the STATUS register may
be read to check the status of the WIP, WEL, BP1 and
BP0 bits (Figure 3-6). A read attempt of a memory
array location will not be possible during a write cycle.
When the write cycle is completed, the write enable
latch is reset.
TABLE 3-1:
INSTRUCTION SET
Instruction Name
READ
WRITE
WRDI
WREN
RDSR
WRSR
Instruction Format
0000 A 8 011
0000 A 8 010
0000 0100
0000 0110
0000 0101
0000 0001
Description
Read data from memory array beginning at selected address
Write data to memory array beginning at selected address
Reset the write enable latch (disable write operations)
Set the write enable latch (enable write operations)
Read STATUS register
Write STATUS register
Note:
A 8 is the
9 th
address bit necessary to fully address 512 bytes.
? 2006 Microchip Technology Inc.
DS21204E-page 7
发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

*型号 *数量 厂商 批号 封装
添加更多采购

我的联系方式

*
*
*
相关PDF资料
25C080-I/P IC EEPROM 8KBIT 3MHZ 8DIP
25C320-E/P IC EEPROM 32KBIT 3MHZ 8DIP
25LC010AT-E/MC IC EEPROM 1KBIT 10MHZ 8DFN
25LC040AT-E/MC IC EEPROM 4KBIT 10MHZ 8DFN
25LC080A-I/STG IC EEPROM 8KBIT 10MHZ 8TSSOP
25LC1024T-E/MF IC EEPROM 1MBIT 20MHZ 8DFN
25LC128-E/MF IC EEPROM 128KBIT 10MHZ 8DFN
25LC160/P IC EEPROM 16KBIT 2MHZ 8DIP
相关代理商/技术参数
25C040X-E/P 制造商:MICROCHIP 制造商全称:Microchip Technology 功能描述:4K SPI ⑩ Bus Serial EEPROM
25C040X-E/SN 制造商:MICROCHIP 制造商全称:Microchip Technology 功能描述:4K SPI ⑩ Bus Serial EEPROM
25C040X-E/ST 功能描述:电可擦除可编程只读存储器 512x8 - 5V Rot Pin RoHS:否 制造商:Atmel 存储容量:2 Kbit 组织:256 B x 8 数据保留:100 yr 最大时钟频率:1000 KHz 最大工作电流:6 uA 工作电源电压:1.7 V to 5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-8
25C040X-EST 制造商:未知厂家 制造商全称:未知厂家 功能描述:SPI Serial EEPROM
25C040X-I/P 制造商:MICROCHIP 制造商全称:Microchip Technology 功能描述:4K SPI ⑩ Bus Serial EEPROM
25C040X-I/SN 制造商:MICROCHIP 制造商全称:Microchip Technology 功能描述:4K SPI ⑩ Bus Serial EEPROM
25C040X-I/ST 功能描述:电可擦除可编程只读存储器 512x8 - 5V Rot Pin RoHS:否 制造商:Atmel 存储容量:2 Kbit 组织:256 B x 8 数据保留:100 yr 最大时钟频率:1000 KHz 最大工作电流:6 uA 工作电源电压:1.7 V to 5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-8
25C040X-I/STG 功能描述:电可擦除可编程只读存储器 512x8 - 5V Rot Pin Lead Free Package RoHS:否 制造商:Atmel 存储容量:2 Kbit 组织:256 B x 8 数据保留:100 yr 最大时钟频率:1000 KHz 最大工作电流:6 uA 工作电源电压:1.7 V to 5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-8